Description:
The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge Controllers are the revolutionary features first developed by OutBack Power, including support for a wide range of nominal battery voltages and the ability to step-down a higher voltage solar array to recharge a lower voltage battery bank. A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration.
FLEXmax MPPT Charge Controllers are the only choice when you demand a high performance, efficient and versatile charge controller for your advanced power system.
The Classic 150 MPPT Charge Controller is MidNite Solar’s most popular model. It has Arc Fault, Ground Fault, free web monitoring, a graphics panel and Solar, Hydro and Wind Modes. The Classic 150 has a maximum output current of 96 amps, an operating voltage of 150 volts and works with 12 to 72 volt battery systems. The FREE MidNite Solar Local Application enables you to monitor your Classics over your local network or the Internet. As with the whole Classic Line, the Classic 150 has MidNite’s exclusive HyperVOC which extends VOC limits when needed.
CLASSIC 200
The Classic 200 MPPT Charge Controller has Arc Fault, Ground Fault, free web monitoring, a graphics panel and Solar, Hydro and Wind Modes. The Classic 200 has a maximum output current of 79 amps, an operating voltage of 200 volts and works with 12 to 72 volt battery systems. The FREE MidNite Solar Local Application enables you to monitor your Classics over your local network or the Internet. As with the whole Classic Line, the Classic 200 has MidNite’s exclusive HyperVOC which extends VOC limits when needed.
CLASSIC 250-SL
The Classic SL-250 MPPT Charge Controller is a simplified SOLAR ONLY version of the Classic 250 with streamlined menus. The Classic SL-250 has a graphics panel and ground fault but no arc fault or Ethernet capabilities. The Classic SL-250 has a maximum output current of 63 amps, an operating voltage of 250 volts and works with 12 to 72 volt battery systems. As with the whole Classic line, the Classic 250-SL has MidNite’s exclusive HyperVOC which extends VOC limits when needed. With a streamlined menu, these SOLAR only MPPT charge controllers are easy to setup and a breeze to install!
Description:
MPPT:
Maximum Power Point Tracking technology for increased PV power output efficiency.
Multi-state Charging:
Maximizes system performance and improves battery life.
Optimal Battery Charging:
Maximizes system performance and improves battery life.
Voltage Options:
Compatible with 12, 24, or 48V battery systems with automatic detection of system voltage.
GFDI:
Integrated PV Ground- Fault Detection and Interruption/ Indication, with pre-fault leakage/ diagnostic metering.
Extensive Electronic Protection:
Over-temperature protection, power derating when temperature is high, PV short circuit and high PV input shutdown, output overcurrent protection and night-time back-feed (reverse current) protection.
Support a Large PV Array:
A single controller supports a large PV array up to 6600W.
High Efficiency:
The PT-100 provides higher than 99% conversion efficiency and uses less than two watts of power in nighttime mode.
Morningstar’s TriStar MPPT 600V charge controller leverages Morningstar’s innovative TrakStar™ MPPT technology and our 20+ years of power electronics engineering excellence, to enable the widest input operating voltage range available from a solar array, wind turbine or hydro input. This controller’s standard and DB versions are for off-grid applications, and the TR versions were developed to enable retrofitting grid-tied systems with battery backup:
- TS-MPPT-60-600V-48
(Standard) - TS-MPPT-60-600V-48-DB
(With Disconnect Box) - TS-MPPT-60-600V-48-DB-TR
(With DC Transfer Switch) - TS-MPPT-60-600V-48-DB-TR-GFPD
(Pre-wired with Ground Fault Protection Device)
Rated for 60 Amps, the TriStar MPPT 600V controller does much more than efficiently charge batteries; it also provides remote communications, data logging, adjustability and metering. In fact, the TriStar MPPT 600V controller is the only 600-volt PV controller to offer open communication protocols and true Ethernet-enabled functionality.
Key Features & Benefits:
The TriStar MPPT 600V charge controller delivers high reliability and excellent performance and features:
- 97.9% peak efficiency.
- Morningstar’s advanced 4-stage charging algorithm to optimize battery health
- Robust thermal, mechanical and electrical design
- Environmentally optimized and equipped with extensive electronic protections
- Industry standard open communication protocols and interfaces for system networking, monitoring and communications
- Superior lightning protection from nearby lightning-induced voltage/current spikes
Applications:
The TriStar MPPT 600V charge controller’s high voltage capability and flexible design enable several application scenarios including:
- Adding modules incrementally with no string sizing issues
- Off-grid PV systems greater than 150 Voc with long wire runs from the array to the controller
- New installation grid-tie PV systems with battery back-up
- Retrofitting string PV inverter systems to later add battery back-up without changing the PV array configuration
- Battery-based Wind systems
- Water pumping applications
- PWM Charge Controllers
- PWM Charge Controllers
SL-10L-24V, SL-10L-12V, SL-20L-24V, SL-20L-12V
Morningstar’s SunLight™ solar lighting controller combines the SunSaver design with an advanced microcontroller for automatic lighting control functions. Four Versions Available: • 12 Volt: 10 and 20 amp ratings • 24 Volt: 10 and 20 amp ratings Warranty 5 Years Model Numbers SL-10L-24V, SL-10L-12V, SL-20L-24V, SL-20L-12V Key Features and Benefits • Microcontroller digital accuracy • Fully automatic operation • Ten field adjustable lighting control options • Special on/off/on lighting functions • Manual test capability • LVD override protection • Detects day and night using the PV array • Suitable for all 12/24 Vdc lamps • Sealed/Flooded battery select • Temperature compensation • Parallel with a SunSaver for 40 amps solar • Includes SunSaver battery charging circuit.
